Informe USA

Elementos 2601 a 2800 de un total de 3582

En sentido ascendente
por página

Lista  Parrilla 

  • ASTM Research Report RR:E33-1012

    An interlaboratory study was conducted by laboratories testing six samples to establish a precision statement for test method E1050.
    1/1/2008 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D13-1122

    An interlaboratory study was conducted by five laboratories testing nine cotton samples to establish a precision statement for test method D1447.
    1/12/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D27-1018

    An interlaboratory study was conducted by twelve laboratories which tested four materials to establish the precision statement of test method D6786.
    1/12/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D35-1011

    An interlaboratory study was conducted by nine laboratories which tested one material to establish the precision statement of test method D7179.
    1/12/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:E28-1027

    An interlaboratory study was conducted by eight laboratories testing two low carbon sheet steel samples to establish a precision statement for test method E646.
    1/12/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F04-1010

    An interlaboratory study was conducted by eleven laboratories testing three samples to establish a precision statement for test method F2516.
    1/12/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:F23-1007

    An Interlaboratory evaluation of test method F739 was performed in 2005. Nine independent laboratories participated, each testing in triplicate, two, challenge chemical/clothing material pairs. The challenge chemicals were acetone and ethanol.
    7/11/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D01-1139

    Interlaboratory Study to Establish Precision Statements for ASTM D7358-07, Standard Test Method for Water Content of Water- Reducible Paints by Quantitative Calcium Hydride Reaction Test Kit
    1/11/2007 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1627

    An interlaboratory study was conducted by twenty laboratories testing thirteen samples to establish a precision statement for test method D7397.
    1/11/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D08-1013

    An interlaboratory study was conducted by ten laboratories which tested three materials to establish the precision statement of test method D5147.
    1/11/2007 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D18-1014

    An interlaboratory study was conducted by twenty-four laboratories testing a single sample of rigid polyurethane foam to establish a precision statement for test method D2166.
    15/10/2007 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D02-1624

    An interlaboratory study was conducted by five laboratories which tested sixteen materials to establish the precision statement of test method D7371.
    1/10/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:F03-1016

    An interlaboratory study was conducted by seven laboratories which tested three materials to establish the precision statement of test method F2523.
    1/10/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1640

    This interlaboratory study to establish precision statements for ASTM D7347 was performed according to this method with five denatured alcohols run in duplicate at five laboratories.
    1/8/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1619

    An interlaboratory study was initiated using two vapor pressure methods, ASTM D5191 and D6378. This study established a precision and bias statement for D6378 and evaluated the precision and bias statement for D5191. Finally, this report compared the precision statements of D5191 versus D6378.
    20/7/2007 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D02-1620

    An interlaboratory study was conducted to establish a precision statement for D7346, Standard Test Method for No Flow Point of Petroleum Products.
    15/7/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1621

    An interlaboratory study was conducted by laboratories which tested thirty three materials to establish the precision statement of test methods D86, D7345, and D7344.
    15/7/2007 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D02-1622

    The precision of ASTM D2622 was determined by the statistical analysis of results obtained from an interlaboratory study that included 27 samples including gasolines, distillates, biodiesel, residual oils, and crude oils. A pooled limit of quantitation (PLOQ) of approximately 3 mg/kg S, was determined for all sample types. Precision for gasoline and diesel samples, as well as for high- power and low-power source XRF instruments were also determined.
    15/7/2007 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1623

    An interlaboratory study was conducted by seventeen laboratories which tested seven ester-based and eight non-ester-based automotive transmission fluids to establish the precision statement of test method D7214.
    15/7/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E28-1025

    An interlaboratory study performed by one laboratory which tested five different materials that spanned a wide range of hardness and modulus to establish an initial precision and bias statement for E2546.
    2/7/2007 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:C21-1005

    An interlaboratory study which involved seven laboratories testing five materials to establish a precision statement for test method C1028.
    1/7/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D01-1137

    An interlaboratory study was performed by seven laboratories that tested four samples was conducted to establish a precision statement for test method D2066.
    1/7/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:E12-1003

    An interlaboratory study was conducted using three photo luminescent film samples which were tested by eight laboratories to establish a precision statement for test method E2073.
    1/7/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D01-1135

    An interlaboratory study was performed by seven laboratories testing five materials was conducted in 2006 to establish a precision statement for the test method D4060.
    1/6/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D05-1032

    An interlaboratory study to establish a precision statement for test method D6342 for the determination of major and minor elements in ash from coal, coke, and solid combustion residues.
    1/6/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D05-1033

    The purpose of this interlaboratory test study is to analyze various types of ash from different sources (laboratory, utility processes, etc.) for total sulfur by high temperature combustion using a promoter so that a precision statement for test method D5016 could be established.
    1/6/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D19-1195

    An interlaboratory study was conducted by six laboratories testing five samples to establish a precision statement for ASTM D7283.
    1/6/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D35-1010

    An interlaboratory study which involved ten laboratories testing three materials to establish a precision statement for test method D7056.
    1/6/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E28-1024

    An interlaboratory study performed by one laboratory which tested six materials to establish the precision statement of test method E2492.
    1/6/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:A05-1003

    An interlaboratory study was conducted to establish a precision statement for A90/A90M.
    1/5/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D05-1031

    An Interlaboratory Study was conducted to establish a precision statement for D7348.
    1/5/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D08-1012

    An interlaboratory study was run in which randomly drawn test specimens of three materials (sand-surfaced SBS-modified base sheet, fiberglass-reinforced SBS-modified cap sheet, and polyester-reinforced APP-modified cap sheet) were tested for machine direction (MD) tear strength and cross-machine direction (CD) tear strength in each of ten laboratories to establish a precision statement for the section of tear strength in test method D5147.
    1/5/2007 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D13-1121

    IAn interlaboratory study was conducted by six laboratories testing three samples to establish precision statements for ASTM D7330.
    1/5/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:E28-1023

    An interlaboratory study was conducted to establish a precision statement for E0010, Brinell Hardness of Metallic Materials.
    24/4/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E28-1022

    An interlaboratory study was conducted for test method E18 to represent the change in the precision statement from the use of steel balls to carbide balls for all scales that use a ball indenter.
    20/4/2007 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D19-1179

    This round robin was intended to generate precision and bias data that is representative of the waters coved in the scope of this ASTM method, D7315. This study covered the approximate range of 1 to 4000 turbidity units. The round robin was well represented by a host of different turbidity technologies that varied among the following criteria: Light source, Single versus multiple detectors and Detection angles.
    15/4/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E33-1011

    An interlaboratory study for test method C423 was conducted by ten laboratories to determine whether uncertainty in measuring decay rate contributed significantly to the uncertainty seen in interlaboratory comparison of sound absorption measurements and establish precision statements for the test method.
    11/4/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1617

    Research report D02-1617 describes an interlaboratory study to establish precision statements for ASTM D87, standard test method for melting point of petroleum wax (cooling curve).
    19/3/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1616

    This report is the analysis of the data from the international round robin tests to establish precision statements for ASTM D5706 organized by the DIN 51834 working group testing in 2005 with 1 mm of stroke and with 2 mm of stroke in 2006.
    15/3/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1614

    The precision of this test method was determined by the statistical evaluation of the interlaboratory test results. For measuring total chloride, both methods of suppression provided a single precision statement. For total and potential sulfate, the data indicated two distinct statistical populations, reflecting use of the packed bed tri-chamber suppressor regeneration approach and the continuous suppressor membrane regeneration approach.
    12/3/2007 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:D02-1615

    An interlaboratory study was conducted to establish a precision statement for D7318, Test Method for Total Inorganic Sulfate in Ethanol by Potentiometric Titration.
    12/3/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1613

    The precision of test method D4684 was determined by the statistical examination of results from an interlaboratory program in which 10 to 11 samples were tested in 7 to 9 laboratories at -25, -30, -35 and -40 degrees C utilizing thermo-electric cooled MRV',s.
    7/3/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:C16-1033

    An interlaboratory study was conducted by six laboratories testing five different materials to establish a precision statement and bias statement for test method C0209.
    1/3/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F17-1049

    An interlaboratory study was conducted by three laboratories which tested six materials to establish the precision statement of test method F2263.
    1/3/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1612

    The precision statement of test method D4684 was determined by the statistical examination of results from an interlaboratory program in which 10 to 11 samples were tested in 7 to 9 laboratories at -25, -30, -35 and -40 degree C utilizing thermo-electric cooled MRV',s.
    20/2/2007 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D01-1140

    An interlaboratory study was conducted by one laboratory which tested five materials to establish the precision statement of test method D7245.
    1/2/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D26-1019

    An interlaboratory test was undertaken to determine the precision and bias of standard test method D2106 Method C in which the amine is determined by gas chromatography per ASTM D6806 and the amine acid acceptance is calculated from the amount of amine present. Two different amines were tested.
    1/2/2007 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:C09-1032

    An interlaboratory study was conducted which involved five operators and three concrete mixtures to establish precision values for ASTM test method C403/C403M.
    29/1/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D01-1136

    An interlaboratory study was performed by nine laboratories that tested four different materials to establish a precision statement for test method D4960.
    16/1/2007 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D16-1035

    An interlaboratory study was conducted by 36 laboratories testing eight samples to establish a precision statement for ASTM D7183.
    15/1/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1610

    An interlaboratory study was performed by twelve laboratories on six used railroad diesel engine oils to establish a precision statement for test method D7317.
    10/1/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1611

    An interlaboratory study was conducted to establish the precision statement of test method D7328.
    1/1/2007 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASME STP-PT-006-2007

    Design Guidelines for Hydrogen Piping and Pipelines
    1/1/2007 - PDF DRM - Inglés - ASME
    Más información
    47,00 €

  • ASTM Research Report RR:C01-1010

    An interlaboratory study was conducted by seven laboratories which measured chemical shrinkage of a single Portland cement that was distributed in vacuum-sealed bags to establish the precision statement of test method C1608.
    21/12/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1608

    An interlaboratory study was performed by ten laboratories analyzing nine grease samples to establish a precision statement for test method D7303.
    20/12/2006 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D08-1010

    An interlaboratory study was run in which randomly drawn test specimens of three materials (sand-surfaced SBS-modified base sheet, fiberglass-reinforced SBS-modified cap sheet, and polyester-reinforced APP-modified cap sheet) were tested in eleven laboratories to establish a precision statement for the selvage thickness test method in ASTM D5147.
    20/12/2006 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D08-1011

    An interlaboratory study was run in which randomly drawn test specimens of three materials (sand-surfaced SBS-modified base sheet, fiberglass-reinforced SBS-modified cap sheet, and polyester-reinforced APP-modified cap sheet) were tested in eleven laboratories to establish a precision statement for the sheet thickness test method in ASTM D5147.
    20/12/2006 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:E33-1010

    An interlaboratory study was conducted that had the participation of sixteen laboratories to establish the precision and bias statement of test method C423.
    19/12/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1648

    An interlaboratory study was conducted by eight laboratories testing four samples to establish a precision statement for test method D7280.
    12/12/2006 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1607

    An interlaboratory study was conducted to establish precision statements for test method D6895.
    8/12/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1605

    An interlaboratory study was conducted to establish the precision statement for test method D6549.
    7/12/2006 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:D02-1606

    An interlaboratory study was conducted to establish the precision statement of test method D6482.
    7/12/2006 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:E01-1061

    An interlaboratory study to justify the revision of the scope of test method E539 to include the elements: chromium, copper, manganese, molybdenum nickel, silicon, tin, and zirconium.
    7/12/2006 - PDF - Inglés - ASTM
    Más información
    102,90 €

  • ASTM Research Report RR:F11-1018

    An interlaboratory study was conducted by eight laboratories which tested five materials to establish the precision statement of test method F2607.
    16/11/2006 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D34-1018

    An interlaboratory study was conducted by laboratories testing samples to establish a precision statement for test method D7203, Standard Test Method for Screening Trichloroethylene (TCE)-Contaminated Media Using a Heated Diode Sensor.
    11/11/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1602

    An interlaboratory study which involved 10 laboratories and 15 test samples to establish the precision statements for ID and DCN in test method D6890.
    19/9/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:F04-1009

    An interlaboratory study was conducted by six laboratories which tested two different materials to establish the precision statement of test method F2082.
    15/8/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1618

    Long-standing criticism of the relatively poor precision of the important ASTM Test Method D 892 was addressed in a 2003 Interlaboratory Study (Round Robin) in attempts to optimize the operation of the method and improve its precision. The twelve (12) participating laboratories included ten (10) user laboratories, one commercial test laboratory and one foam test instrument manufacturer',s laboratory. Eight of the laboratories used liquid baths and four used air baths.
    1/8/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:F02-1023

    An interlaboratory study was conducted by eighteen laboratories which tested three material combinations with a series of techniques to establish the precision statement of test method F88.
    10/7/2006 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:C01-1008

    Two interlaboratory studies were conducted to establish a precision statement for C-359. Test method C-359 prior to this study lacked a precision and bias statement. Inter-laboratory testing programs conducted in 2004 and 2005 provided data sufficient to construct such a statement using indexes derived from the measured data. This report details the Inter-laboratory results, the derivation of the indexes and the precision statements for those indexes.
    1/7/2006 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:E12-1002

    An interlaboratory study was conducted by one laboratory testing 6 specimens to provide data representative of the precision and bias for measurements made in accordance with test method E991.
    1/7/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F11-1017

    An interlaboratory study which involved five laboratories and four central vacuum cleaning units was conducted to establish the precision and bias statement of test method F2544.
    1/7/2006 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1591

    An interlaboratory study was conducted by eighteen laboratories analyzing five oil samples to establish a precision statement for test method D7214.
    13/6/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:E01-1060

    An interlaboratory study was conducted by six laboratories which tested sixteen materials to establish the precision statement of test method E2465.
    30/5/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:B09-1012

    An interlaboratory study was conducted to establish a precision statement for ferrous and copper base sintered parts for ASTM test method B328.
    29/4/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E12-1001

    An interlaboratory study was conducted by two organizations which used sixteen instruments in nine different models to collect three replicate readings of twelve ceramic color standards so a precision statement could be established for test method E1349.
    30/3/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1603

    An interlaboratory study to establish a precision statement for the free and total glycerin in test method D6584.
    1/3/2006 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1604

    An interlaboratory study was performed using 10 used and 5 fresh oil samples (viscosity range 25 to 150 mm2/s at 40�,C and 6 to 16 mm2/s at 100�,C) and 15 laboratories, to establish the precision statement in test method D7279.
    1/3/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D01-1134

    An interlaboratory study was conducted for D1316 using Manual and Automatic (ADM-1) procedures of the test method in which one operator in each of seven labs used both manual and automatic (ADM-1) methods.
    22/2/2006 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D02-1589

    An interlaboratory study was conducted by nine laboratories testing six samples for small vials that ranged from 0.1% to 25% to establish a precision statement for test method D4530.
    15/2/2006 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1587

    An interlaboratory study was conducted by nine laboratories testing six gasoline samples and six diesel fuel samples to establish a precision and bias statement for test method D7212.
    1/2/2006 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D20-1242

    An interlaboratory study was conducted by ten laboratories testing four samples to establish a precision statement for the CIELAB color in test method D7133.
    18/1/2006 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • The Science of Stainless Steel Produced by Powder Metallurgy and Metal Injection

    Metal Powder Industries Federation, 2006
    1/1/2006 - PDF - Inglés - MPIF
    Más información
    150,00 €

  • ASTM Research Report RR:E37-1035

    An interlaboratory study was conducted in which thirteen laboratories using four instrument models from two manufacturers tested calibration slope to establish the precision statement of test method E2206.
    22/12/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E37-1036

    An interlaboratory study was conducted by eight laboratories which tested two materials to establish the precision statement of test method E2403.
    22/12/2005 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1584

    An interlaboratory study was conducted to establish a precision statement for test method D5864. Five laboratories ran this study by testing ten different lubricants and base stocks.
    13/12/2005 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:E28-1026

    An intralaboratory study was conducted by a single laboratory which tested six samples to establish a precision statement for test method E2448.
    1/12/2005 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • API OCTG04:2005

    Report of Eastern/Western Hemisphere Production of Casing, Tubing, and Drill Pipe
    1/11/2005 - PDF sécurisé - Inglés - API
    Más información
    185,00 €

  • ASTM Research Report RR:F04-1008

    An interlaboratory study was conducted by seven laboratories which tested three materials to establish the precision statement of test method F2004.
    1/10/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E01-1040

    An interlaboratory study was conducted by ten laboratories which tested three materials to establish the precision statement of test method E1915.
    27/9/2005 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:E37-1034

    An interlaboratory study was conducted by twelve laboratories using six instrument models from three manufacturers to establish the precision statement of test method E2347.
    12/9/2005 - PDF - Inglés - ASTM
    Más información
    102,90 €

  • ASTM Research Report RR:C16-1032

    An interlaboratory study on the breaking load and flexural properties of block-type thermal insulation was conducted in 2005 to establish precision statements for C203. The eight laboratories participating in the study measured the breaking load/flexural property of five randomly selected samples of four different block-type EPS/XPS thermal insulations at two different cross-head speeds.
    16/8/2005 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1580

    An interlaboratory study was conducted to establish a bias statement for test method D86 by comparing the manual and the automated apparatus and procedures.
    8/8/2005 - PDF - Inglés - ASTM
    Más información
    102,90 €

  • ASTM Research Report RR:D02-1579

    An interlaboratory study was run by laboratories testing lubricating test oils at 80�,C and 120�,C to establish a precision statement for test method D6425.
    25/7/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D16-1034

    An interlaboratory study performed by three laboratories which tested five materials to establish the precision statement of test method D6143.
    20/7/2005 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:C09-1031

    An interlaboratory study was conducted to establish precision values for nuclear gages operating in the direct transmission mode when testing unhardened concrete according to test method C1040.
    19/7/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1592

    A round robin was carried out in 2004 involving two EDXRF based methods based on (i) a low-background proportional detector and (ii) polarized source for sulfur determination in the range 1 to 60 mg/kg. This resulted from a recommendation from the 2002 round robin report of CEN TCI9 WG27 to investigate the precision of new generation EDXRF equipment once it became more widely available. Due to the interest in low level sulfur measurement ( 50 mg/kg and less) in fuels was becoming of increasing relevance in both Europe and the USA, it was decided to carry out a joint EI/ASTM exercise using fuels of interest sourced from both areas. Nine laboratories participated in the low-background proportional detector method and eleven laboratories in the polarization method.
    29/6/2005 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:D02-1588

    An interlaboratory study was conducted to establish a precision statement for test method D2624.
    15/6/2005 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D02-1586

    An interlaboratory study was run by eight laboratories testing ten samples to establish the precision statement of test method D7224.
    6/6/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D18-1008

    An interlaboratory study performed by three laboratories which tested three materials to establish the precision statement of test method D698.
    2/6/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D18-1009

    An interlaboratory study performed by three laboratories which tested four reference soils to establish the precision statement of test method D854.
    2/6/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D18-1010

    An interlaboratory study performed by three laboratories which tested four reference soils to establish the precision statement of test method D1140.
    2/6/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D18-1011

    An interlaboratory study was conducted by laboratories which tested soil samples of reference soil SP-1 to establish a precision statement for specifications D4253 and D4254.
    2/6/2005 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D18-1013

    An interlaboratory study performed by three laboratories which tested three materials to establish the precision statement of test method D4318.
    2/6/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D19-1184

    Interlaboratory Study to Establish Precision Statements for ASTM D7168, Standard Test Method for 99Tc in Water by Solid Phase Extraction Disk
    1/6/2005 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D20-1244

    An interlaboratory test was conducted by seven laboratories testing four samples to establish a precision statement for test method D7253. Each laboratory used a colorimetric endpoint titration for the generation of the data used to develop the statement.
    1/6/2005 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F02-1022

    An interlaboratory study was conducted by eight laboratories which tested five materials to establish the precision statement of test method D3985.
    1/6/2005 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1575

    An interlaboratory study was conducted to determine if a new Digital Conductivity Meter, Model 1153 was equivalent to the Emcee Model 1152 Digital Conductivity Meter. This study demonstrated that the two models were equivalent and the repeatability data that was obtained by this study is in the test method D2624.
    24/5/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1582

    An interlaboratory study was run by nine laboratories testing ten test oils to establish a precision statement for test method D7109.
    19/5/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:C09-1029

    Interlaboratory Study to Establish Precision Statements for ASTM C1580, Standard Test Method for Water-Soluble Sulfate in Soil
    4/5/2005 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1599

    In an interlaboratory study, molybdenum was determined by analyzing ten oil and eight additive samples by participating laboratories so that a precision statement could be established for test method D4951.
    1/5/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1577

    This report documents two interlaboratory studies to generate precision data for test method D7171 for the determination of the mass percent of hydrogen in middle distillate petroleum products by low-resolution pulsed nuclear magnetic resonance spectroscopy.
    19/4/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:C16-1031

    Research report C16-1031 describes an interlaboratory study performed by four laboratories that reports the warpage results to determine the precision and bias of C411.
    7/4/2005 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1569

    This report documents two interlaboratory studies to generate precision data for test method D7111 for quantitative analysis of trace elements in middle distillate fuels.
    5/4/2005 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:C24-1055

    Research Report C24-1055 establishes precision statements for C1635. Two interlaboratory studies were conducted. The first study had five laboratories test five sealants. The second study had five laboratories test two sealants.
    24/3/2005 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:D13-1120

    An interlaboratory study was conducted by eight laboratories testing four fabric samples to establish a precision statement for test method D7142.
    4/3/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • API Publ 2383:2005

    2004 Survey on Petroleum Industry Occupational Injuries, Illnesses, and Fatalities Summary Report: Aggregate Data Only
    1/3/2005 - PDF sécurisé - Inglés - API
    Más información
    123,00 €

  • ASTM Research Report RR:D02-1593

    An interlaboratory study was conducted involving thirteen laboratories and eight samples comprising three diesel fuels, two kerosines, two JetA/A1 fuels and hexadecane to establish a precision statement for test method D7236.
    20/2/2005 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F02-1021

    An interlaboratory study was conducted by eight laboratories which tested five materials to establish the precision statement of test method D3985.
    3/2/2005 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:C16-1029

    An interlaboratory study was conducted at six laboratories testing seven samples to establish a precision statement for linear shrinkage tests in test methods C1427 and C534.
    10/1/2005 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D27-1017

    An Intralaboratory Study was conducted to estimate the repeatability by one laboratory for 7 replicates of a fluid containing a nominal 1 ppm by weight.
    1/1/2005 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • WRC Volume 60 No. 09-10 2005

    Progress Reports Volume 60 No. 09-10 2005
    1/1/2005 - PDF sécurisé - Inglés - WRC
    Más información
    102,00 €

  • WRC Volume 60 No. 07-08 2005

    Progress Reports Volume 60 No. 07-08 2005
    1/1/2005 - PDF sécurisé - Inglés - WRC
    Más información
    102,00 €

  • WRC Volume 60 No. 05-06 2005

    Progress Reports Volume 60 No. 05-06 2005
    1/1/2005 - PDF sécurisé - Inglés - WRC
    Más información
    102,00 €

  • WRC Volume 60 No. 03-04 2005

    Progress Reports Volume 60 No. 03-04 2005
    1/1/2005 - PDF sécurisé - Inglés - WRC
    Más información
    102,00 €

  • WRC Volume 60 No. 11-12 2005

    Progress Reports Volume 60 No. 11-12 2005
    1/1/2005 - PDF sécurisé - Inglés - WRC
    Más información
    102,00 €

  • ASME STP/PT-003-2005

    Hydrogen Standardization Interim Report for Tanks, Piping, and Pipelines (STP/PT-003 - 2005)
    1/1/2005 - PDF DRM - Inglés - ASME
    Más información
    38,00 €

  • ASTM Research Report RR:D02-1585

    An interlaboratory study was conducted by ten cooperators testing two different solid bonded films to establish the precision statement for test method D7217.
    22/12/2004 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1565

    An interlaboratory study was conducted to establish a precision statement for Procedure B of test method D5706.
    16/12/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:C09-1028

    An interlaboratory study was conducted by eleven operators testing two concrete batches at around 75°, C to establish precision statements for test method C1064/C1064M.
    15/12/2004 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:C09-1027

    This report consists of analysis of the results from an interlaboratory study conducted to develop precision data for the tests covered by ASTM Test Method C 796. Three laboratories provided data that were analyzed using the ASTM Practice E 691 software.
    9/12/2004 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1555

    An interlaboratory study was conducted by twelve laboratories to establish a precision statement for test method D7042.
    3/12/2004 - PDF - Inglés - ASTM
    Más información
    102,90 €

  • ASTM Research Report RR:D19-1177

    An interlaboratory study performed by eight laboratories which tested ten samples to establish the precision statement of test method D5673.
    3/12/2004 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:D13-1119

    An interlaboratory study was conducted by five laboratories which tested three materials to establish the precision statement of test method D5587.
    28/10/2004 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F11-1016

    An interlaboratory study was conducted by twelve laboratories which tested four materials to establish the precision statement of test method F888.
    28/10/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D32-1040

    An interlaboratory study was conducted by three laboratories which tested three materials to establish the precision statement of test method D7084.
    27/10/2004 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D05-1029

    An interlaboratory study was conducted to establish a precision statement for test method D6357.
    22/10/2004 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D20-1243

    An interlaboratory test was conducted by seven laboratories testing six samples to develop estimates of data on a precision and bias statement for test method D7252.
    1/9/2004 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:G01-1021

    An interlaboratory study was conducted by six laboratories which tested four materials to establish the precision statement of test method G180.
    12/8/2004 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:C14-1004

    An interlaboratory round robin testing was conducted in accordance with Practice E 691 to establish the precision and bias of edge stress measurement (Procedure B) for C1279.
    1/8/2004 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1562

    An interlaboratory study was run by six laboratories that analyzed forty-six samples to establish a precision statement for test method D7095.
    30/7/2004 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1572

    An interlaboratory study to establish the precision statement for test method D2386 was run by fifteen laboratories testing thirteen samples of fuel consisting of Jet A, Jet A1, JP-5 and JP-8.
    20/7/2004 - PDF - Inglés - ASTM
    Más información
    102,90 €

  • ASTM Research Report RR:D13-1118

    An interlaboratory study was conducted by four laboratories testing four sewing thread and two mattress tapes to establish a precision statement for test method D7016.
    16/7/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D01-1133

    An interlaboratory study of test method D7189 was conducted in which one operator in each of four laboratories participated in round robin testing of five samples of news ink blacks of varying percentages of carbon black pigmentation.
    24/6/2004 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D16-1033

    An interlaboratory study performed by five laboratories which tested five materials to establish the precision statement of test method D7057.
    3/6/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1581

    An interlaboratory study was conducted involving eight laboratories and using two pure chemicals, eleven fuels and four lubricating oils, to establish the precision statement for test method D7094.
    1/6/2004 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:F11-1015

    An interlaboratory study was conducted by six laboratories which tested seven materials to establish the precision statement of test method F2105.
    10/5/2004 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:E28-1021

    An interlaboratory study was conducted by fourteen laboratories which tested six materials to establish the precision statement of test method E18.
    3/5/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D16-1032

    This round robin was conducted in support of a revision of an existing test method, D3760, Analysis of Isopropyl Benzene (Cumene) by Capillary Gas Chromatography, to update the components identified and switch to calibration of the gas chromatography system by the external standard technique. The method was found to be applicable to the measurement of impurities such as nonaromatic hydrocarbons, benzene, toluene, ethylbenzene, phenol, cymenes, f-butylbenzene, n-butylbenzene, n-propyl benzene, alpha-methyl styrene, sec-butylbenzene, and diisopropylbenzenes. Five laboratories participated.
    5/4/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:E01-1039

    An interlaboratory study was conducted by nineteen laboratories which tested nine materials to establish the precision statement of test method E1335.
    30/3/2004 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:E27-1006

    An interlaboratory study was conducted by thirteen laboratories which tested Constant Temperature Stability of 1-phenyl-1H-tetrazole-5-thiol, known to decompose autocatalytically to establish the precision statement of test method E487.
    17/3/2004 - PDF - Inglés - ASTM
    Más información
    95,55 €

  • ASTM Research Report RR:C16-1026

    An interlaboratory study was conducted by five laboratories testing six different extraction solutions prepared from six different material types of insulation to establish a precision statement for test method C871.
    12/3/2004 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D19-1176

    An interlaboratory study was conducted by 21 laboratories which tested 24 materials to establish the precision statement of test method D7066.
    10/3/2004 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:G01-1022

    An interlaboratory study was conducted by seven individuals which tested three soil samples to establish the precision statement of test method G187.
    29/1/2004 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:F02-1020

    An interlaboratory study was conducted by three laboratories which tested non-lidded semirigid (PETE) thermoformed trays, and trays sealed with various porous barrier lidding materials to establish the precision statement of test method F2338.
    20/1/2004 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D30-1005

    An interlaboratory study was conducted by six laboratories testing six sets of twelve individual specimens to establish a precision statement for test method D6484.
    1/1/2004 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E37-1032

    An interlaboratory study was conducted in which eight laboratories characterized a poly(vinyl chloride) sample in to establish the precision statement of test method E2092.
    18/12/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1552

    An interlaboratory study was conducted by six laboratories testing nineteen samples to establish a precision statement for test method D7039. Only the repeatability precision estimate shown in this report is included in the publication of the test method.
    13/12/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1570

    An interlaboratory study was conducted by six laboratories testing seven sooted oils to establish the precision statement of test method D7710.
    12/12/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1568

    A round robin was conducted to support an upgrade to the viscometer head and software used in test method D5133.
    11/12/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1551

    An interlaboratory study was run by nineteen laboratories testing ten samples to establish a precision statement for test method D664.
    4/12/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1567

    An interlaboratory study was performed by eleven laboratories testing five oils to establish the precision statement for test method D7097.
    1/12/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:E37-1030

    An interlaboratory study was conducted by fourteen laboratories testing two samples to establish a precision statement for test method E2160.
    25/11/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:E37-1031

    An interlaboratory study was conducted by eight laboratories which tested the volatility rates for camphor at 333 K and squalane at 573 K were determined using the isothermal test to establish the precision statement of test method E2008.
    25/11/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:F11-1014

    An interlaboratory study was conducted by seven laboratories testing three samples to establish a precision statement for test method F608.
    4/11/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D14-1011

    An interlaboratory study was performed by five laboratories which tested one adhesive material according to ASTM D6004 and ASTM D686 to establish precision statements for D6004.
    28/10/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:C14-1003

    An interlaboratory study to establish the precision for C1203. Six laboratories performed an analysis on four materials.
    27/10/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:F02-1018

    An interlaboratory study was conducted by seven laboratories which tested eight materials to establish the precision statement of test method F2251.
    27/10/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:C16-1027

    Research report C16-1027 describes an interlaboratory study that documents the estimate of repeatability in C1574.
    10/9/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1598

    An interlaboratory study was conducted involving nine laboratories and twelve middle distillate fuel samples to establish a precision statement for test method D5304.
    1/9/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D20-1238

    An interlaboratory study was conducted by eleven laboratories testing ten materials to establish a precision statement for test method D5132.
    28/8/2003 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D14-1014

    An intralaboratory study was conducted by one laboratory testing three samples to establish a repeatability statement for test method D1875.
    15/8/2003 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D02-1548

    An interlaboratory study was performed by seven laboratories using two different types of Voltammograms to establish a precision statement for test method D6810.
    28/7/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1546

    An interlaboratory study was conducted by ten laboratories to establish a precision statement for test method D3120.
    25/7/2003 - PDF - Inglés - ASTM
    Más información
    98,70 €

  • ASTM Research Report RR:D02-1547

    An interlaboratory study was conducted by 56 laboratories testing sixteen samples of gasoline and diesel to establish precision statements for test methods D2622, D3120, and D5453.
    25/7/2003 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D04-1021

    An interlaboratory study was conducted by laboratories testing five materials to establish a precision statement for test method D3549.
    25/7/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D04-1026

    An interlaboratory study was conducted by six laboratories to establish a precision statement for the test method, coefficient of luminous intensity, in standard specification D4280.
    25/7/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D14-1010

    An interlaboratory study was run in which test specimens of one material (latex-based elastomeric adhesive) was tested for Shear and Tensile strength in each of six laboratories with each laboratory testing one set of five specimens for each strength characteristic to establish precision statements for ASTM D6464.
    25/7/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:E37-1029

    An interlaboratory study was conducted by thirteen laboratories which tested five materials to establish the precision statement of test method E2070.
    25/7/2003 - PDF - Inglés - ASTM
    Más información
    102,90 €

  • ASTM Research Report RR:D20-1236

    An interlaboratory study was conducted by thirteen laboratories testing three materials to establish a precision statement for test method D2578.
    9/7/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D16-1030

    An interlaboratory study performed by six laboratories which tested ten materials to establish the precision statement of test method D5060.
    25/6/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D16-1031

    An interlaboratory study was conducted by six laboratories testing two samples to establish a precision statement for test method D5135.
    25/6/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D20-1194

    An interlaboratory study was conducted by six laboratories including eight materials to establish a precision statement for Vicat Softening Temperature Using Loading 2 and Heating Rate A for test method D1525.
    25/6/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D20-1228

    An interlaboratory study was conducted by nine laboratories testing three materials to establish a precision statement for test method D746.
    25/6/2003 - PDF - Inglés - ASTM
    Más información
    56,70 €

  • ASTM Research Report RR:D20-1237

    An interlaboratory study was conducted by ten laboratories testing five rigid PVC dry blend compounds to establish a precision statement for the test method in standard practice D2538.
    25/6/2003 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:E27-1005

    An interlaboratory study was conducted by ten laboratories which tested five materials to establish the precision statement of test method E2046.
    25/6/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D20-1239

    An interlaboratory study was conducted by seven laboratories testing four materials to establish a precision statement for test method D6979.
    10/6/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:F02-1019

    An interlaboratory study was conducted by three laboratories testing samples to establish a precision statement for test method F2338.
    15/5/2003 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:D02-1542

    An interlaboratory study was conducted by eight operators testing nine identical samples to establish a precision statement for test method D6824.
    6/5/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D02-1544

    An interlaboratory study was conducted to establish a precision statement for test method D6839.
    6/5/2003 - PDF - Inglés - ASTM
    Más información
    115,50 €

  • ASTM Research Report RR:F06-1008

    An interlaboratory study was conducted by six laboratories testing four samples to establish a precision statement for test method F137 and F2055.
    6/5/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D13-1108

    An interlaboratory test was run in 1994 through 1995 in which three randomly-drawn samples were tested in five difference laboratories as directed in D2261. Two operators in each laboratory each tested eight specimens of each material. Four of the eight specimens were tested on one day and four specimens were tested on the second day.
    24/4/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D13-1109

    An interlaboratory study was conducted by eight laboratories testing three woven fabrics and six laboratories testing eight nonwoven fabrics to establish a precision statement for test method D737.
    24/4/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D13-1110

    An interlaboratory test was run in 1994 through 1995 in which randomly drawn samples were tested as directed in the five options of D1777. Six laboratories participated, each testing five materials. Two operators in each laboratory each tested ten specimens of each material. Five of the ten specimens were tested on one day and five were tested on a second day.
    24/4/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

  • ASTM Research Report RR:D13-1111

    An interalaboratory study was conducted by six laboratories testing five samples to establish a precision statement for test method D1388.
    24/4/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D27-1015

    An interlaboratory study was conducted by twelve laboratories which tested four materials to establish the precision statement of test method D924.
    16/4/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D01-1127

    An interlaboratory study of the iodine value of two tall oil fatty acids using two different solvents, was run in 2000 for test method D5768.
    31/3/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1537

    An interlaboratory study was conducted by nine laboratories performing hydroperoxide analyses on a total of seven different samples to establish a precision statement for test method D6447.
    31/3/2003 - PDF - Inglés - ASTM
    Más información
    63,00 €

  • ASTM Research Report RR:D02-1539

    An interlaboratory study was run at six labs using six oils to establish a precision and bias statement for test method B for D2893.
    31/3/2003 - PDF - Inglés - ASTM
    Más información
    81,90 €

  • ASTM Research Report RR:D02-1540

    An interlaboratory study was run by six laboratories testing twelve samples to establish a precision statement for test method D6426.
    31/3/2003 - PDF - Inglés - ASTM
    Más información
    89,25 €

Elementos 2601 a 2800 de un total de 3582

En sentido ascendente
por página

Lista  Parrilla