ASTM D7528-22

ASTM D7528-22

Standard Test Method for Bench Oxidation of Engine Oils by ROBO Apparatus

Disponibilité: En stock.

74,00 €

Détails

1.1 This test method describes a bench procedure to simulate the oil aging encountered in Test Method D7320, the Sequence IIIG engine test method. These aged oils are then tested for kinematic viscosity and for low-temperature pumpability properties as described in the Sequence IIIGA engine test, Appendix X1 of Test Method D7320.

1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1 Exceptions—There are no SI equivalents for some apparatus in Section 6, and there are some figures where inch units are to be regarded as standard.

1.3 This test method is arranged as follows:

 

Section

Scope

1

Reference Documents

2

Terminology

3

Summary of Test Method

4

Significance and Use

5

Apparatus

6

Reagents and Materials

7

Hazards

8

New and Existing Test Stand Calibration

9

Procedure

10

Cleaning

11

Calculations and Determination of Test Results

12

Report

13

Precision and Bias

14

Keywords

15

Annexes

 

ASTM Test Monitoring Center: Organization

Annex A1

ASTM Test Monitoring Center: Calibration Procedures

Annex A2

ASTM Test Monitoring Center: Maintenance Activities

Annex A3

ASTM Test Monitoring Center: Related Information

Annex A4

Reaction Vessel

Annex A5

Reaction Vessel Head

Annex A6

Reaction Vessel-to-Head Seal

Annex A7

Agitator Turbine Blade

Annex A8

Agitator Packing Gland

Annex A9

Nitrogen Dioxide Graduated Tube

Annex A10

Vacuum System Plumbing

Annex A11

Vacuum Trap Condensers

Annex A12

Setting the Vacuum Control Valve

Annex A13

Appendixes

 

Sample Preparation and Addition

Appendix X1

Charging the Liquid Nitrogen Dioxide

Appendix X2

Nitrogen Dioxide Precision Needle Valve

Appendix X3

Example of an Assembled ROBO Apparatus

Appendix X4

Information Package to Aid Setting Up a New Robo Apparatus

Appendix X5

Dilute Nitrogen Dioxide in Air Option Information

Appendix X6

Time-Averaged Subsurface Air Flow Rate

Appendix X7

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Sections 7 and 8.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Significance and Use:

5.1 This bench test method is intended to produce comparable oil aging characteristics to those obtained with ASTM TMC Sequence IIIGA matrix reference oils 434, 435, and 438 after aging in the Sequence IIIG engine test.

5.2 To the extent that the method generates aged oils comparable to those from the Sequence IIIG engine test, the measured increases in kinematic and MRV viscosity indicate the tendency of an oil to thicken because of volatilization and oxidation, as in the Sequence IIIG and IIIGA (see Appendix X1 in Test Method D7320) engine tests, respectively.

5.3 This bench test procedure has potential use in specifications and classifications of engine lubricating oils, such as Specification D4485.

5.4 The results of this test method are valid when seeking qualification of oils against published specifications only when run on a test stand that has successfully met the calibration requirements specified under the TMC’s ROBO test monitoring program.

Informations supplémentaires

Auteur American Society for Testing and Materials (ASTM International)
Comité D02.B0.07 - Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants
Edité par ASTM
Type de document Norme
Thème ,Lubricants, industrial oils and related products
ICS 75.100 : Lubrifiants, huiles industrielles et produits connexes
Nombre de pages 25
Remplace ASTM D7528-21
Recueil ASTM Volume 05.04 - Multi-User - Single-Site Online
Mot-clé D7528

Vous pourriez aussi être intéressé(e) par le(s) produit(s) suivant(s)