ASTM D4050-20 + Redline

ASTM D4050-20 + Redline

Standard Test Method for (Field Procedure) for Withdrawal and Injection Well Testing for Determining Hydraulic Properties of Aquifer Systems

Disponibilité: En stock.

61,00 €

Détails

1.1 ,This test method covers the field procedure for selecting well locations, controlling change (discharge or injection) rates, and measuring water levels used to analyze the hydraulic properties of an aquifer or aquifers and adjacent confining beds.

1.2 ,This test method is used in conjunction with an analytical procedure such as Test Methods D4105/D4105M or D4106 to evaluate the data and determine aquifer properties.

1.3 ,The appropriate field and analytical procedures are selected as described in Guide D4043.

1.4 ,Limitations—,The limitations of this test method are primarily related to the correspondence between the field situation determined by this test method and the simplifying assumptions of the analytical Test Methods D4105/D4105M or D4106 and D4043.

1.5 ,Units—,The values stated in SI units are to be regarded as standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.

1.6 ,All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.6.1 ,The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’,s objectives, and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.

1.7 ,This test method offers a set of instructions for performing one or more operations. This document cannot replace education or experience and should be used in conjunction with professional judgement. Not all aspects of this standard may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projects many unique aspects. The word “,Standard”, in the title of this document means only that the document has been approved through the ASTM consensus process.

1.8 ,This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9 ,This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Significance and Use:

5.1 ,Withdrawal or injection well test field procedures are used with appropriate analytical procedures in appropriate hydrogeological sites to determine transmissivity and storage coefficient of aquifers and hydraulic conductivity of confining beds.

5.2 ,Practice D3740 provides evaluation factors for the activities in this test method.

Note 2: ,The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors, Practice D3740 provides a means of evaluating some of those factors.

5.3 ,This test method may be limited due to the correspondence between the field situation determined by this test method and the simplifying assumptions of the analytical Test Methods D4105/D4105M or D4106 and D4043.

Informations supplémentaires

Auteur American Society for Testing and Materials (ASTM International)
Comité D18.21 - Committee D18 on Soil and Rock
Edité par ASTM
Type de document Norme
Thème ,Water of natural resources
ICS 13.060.10 : Eau d'origine naturelle
Nombre de pages 5
Remplace ASTM D4050-14 + Redline
Recueil ASTM Volume 04.08 - Multi-User - Single-Site Online
Historique ,,,
Mot-clé D4050
Bon de commande

Vous pourriez aussi être intéressé(e) par le(s) produit(s) suivant(s)