49.030.01 : Fasteners in general

123 Item(s)

Set Ascending Direction
per page

List  Grid 

  • 20/30395622 DC:2020

    BS SP 28 and 29 Pins, taper, solid (inch series), corrosion resisting steel and cadmium plated alloy steel. Specification
    5/21/2020 - PDF - English - BSI
    Learn More
    €23.70

  • SAE AS 5869G:2020-05-08

    FITTING ASSEMBLY, UNION, 3 HOLE FLANGE AXIALLY SWAGED, HYDRAULIC 5080 PSI
    5/8/2020 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5767B:2020-04-29

    FITTING ASSEMBLY, TEE, FEMALE FLARELESS ON RUN, AXIALLY SWAGED, HYDRAULIC, 5080 PSI
    4/29/2020 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5793B:2020-04-29

    FITTING ASSEMBLY, STRAIGHT, MALE FLARELESS, AXIALLY SWAGED, HYDRAULIC, 3000 PSI
    4/29/2020 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5791B:2020-04-28

    FITTING ASSEMBLY, STRAIGHT, BULKHEAD FLARELESS, AXIALLY SWAGED, HYDRAULIC, 3000 PSI
    4/28/2020 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5792D:2020-04-28

    FITTING ASSEMBLY, STRAIGHT, FEMALE FLARELESS, AXIALLY SWAGED, HYDRAULIC, 3000 PSI
    4/28/2020 - PDF - English - SAE
    Learn More
    €77.00

  • BS 2SP 94:2019

    Aerospace series. Bushes (plain and flanged), press-fit and thrust washers, oil-retaining sintered bronze. Specification
    10/24/2019 - PDF - English - BSI
    Learn More
    €154.05

  • SAE AS 5170A:2019-07-31

    FITTING, PLUG, PORT, STRAIGHT THREAD, O-RING SEAL
    7/31/2019 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 172321B:2019-07-12

    NUT, SPANNER, AERONAUTICAL, UNS G41400
    7/12/2019 - PDF - English - SAE
    Learn More
    €77.00

  • 19/30397937 DC:2019

    BS EN 6117. Aerospace series. Specification for lubrication of fasteners with cetyl alcohol
    6/24/2019 - PDF - English - BSI
    Learn More
    €23.70

  • SAE AS 3502A:2019-05-24

    INSERT, SCREW THREAD, SELF LOCKING PLASTIC LOCKING DEVICE, SOLID FILM LUBRICATED SELF-BROACHING KEYS, UNS S66286
    5/24/2019 - PDF - English - SAE
    Learn More
    €77.00

  • SAE MA 1520B:2019-05-03

    Areas for Calculating Stress or Load Values for Metric MJ Externally Threaded Fasteners (Stabilized: May 2019)
    5/3/2019 - PDF - English - SAE
    Learn More
    €77.00

  • SAE MAP 1753B:2018-08-09

    Hole Sizes, Recommended for Metric Fasteners on Propulsion Equipment (Stabilized: Aug 2018)
    8/9/2018 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 1325A:2018-06-20

    Wrench Configuration, 12 Lobed Drive (Stabilized: Jun 2018)
    6/20/2018 - PDF - English - SAE
    Learn More
    €77.00

  • SAE ARP 953C:2018-04-19

    Stress Dome in Fasteners (Stabilized: Apr 2018)
    4/19/2018 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 4283C:2017-12-07

    Handles and Attachments for Hand Socket Wrenches
    12/7/2017 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5929B:2017-10-23

    BEARING, ROLLER, NEEDLE, TRACK-ROLLER, CROWN RADIUSED OD, INTEGRAL STUD, TYPE VII, ANTI-FRICTION, CORROSION RESISTANT NITROGEN (CREN) STEEL AND CORROSION RESISTANT (CRES) STEEL, INCH
    10/23/2017 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 70003-1:2017-08-11

    AS70003 Ring, Tube, Welding (Metric & Inch Tube Series)
    8/11/2017 - PDF - English - SAE
    Learn More
    €74.22

  • DIN 65946:2017-07

    Aerospace series - Determination of coefficients of friction of bolts and nuts under specific conditions, Text in German and English
    7/1/2017 - PDF - English, German - DIN
    Learn More
    €89.00

  • SAE AS 893E:2017-06-22

    FITTING, TEE, STANDARD AND REDUCER, FLARELESS TUBE TO PIPE ON SIDE, EXTERNAL THREAD (Stabilized: Jun 2017)
    6/22/2017 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 6471:2017-03-14

    FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC
    3/14/2017 - PDF - English - SAE
    Learn More
    €77.00

  • SAE ARP 5777:2017-02-02

    Maintenance and Inspection Procedures for Acme Screw Assemblies
    2/2/2017 - PDF - English - SAE
    Learn More
    €77.00

  • SAE ARP 5812:2017-02-02

    Actuators, Linear Mechanical, General Specification Guide
    2/2/2017 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AIR 5575A:2017-01-24

    Hot Stamp Wire Marking Concerns for Aerospace Vehicle Applications (Stabilized: Jan 2017)
    1/24/2017 - PDF - English - SAE
    Learn More
    €77.00

  • NF EN 16602-70-46, L90-200-70-46 (01/2017)

    Space product assurance - Requirements for manufacturing and procurement of threaded fasteners - Assurance produit des projets spatiaux - Exigences pour la fabrication et l'approvisionnement de fixations filetées
    1/1/2017 - Paper - English, French - AFNOR
    Learn More
    €110.46

  • SAE AS 6473:2016-10-27

    FITTING, ELBOW, 90°, EXTERNAL SWAGE TO FLARELESS, HYDRAULIC
    10/27/2016 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 6478:2016-10-16

    FITTING, ADAPTER, BULKHEAD, EXTERNAL SWAGE TO MALE FLARELESS, HYDRAULIC
    10/16/2016 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 85028/3A:2016-05-13

    CONNECTOR, ELECTRIC, RECTANGULAR, INDIVIDUAL CONTACT SEALING, POLARIZED CENTER JACKSCREW, INTERFACIAL SEAL, SIZE 16, CRIMP CONTACTS (Stabilized: May 2016)
    5/13/2016 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 85028/4A:2016-05-13

    CONNECTOR, ELECTRIC, RECTANGULAR, INDIVIDUAL CONTACT SEALING, POLARIZED CENTER JACKSCREW, SEALING PLUG, SIZE 16, CRIMP REMOVABLE CONTACTS (Stabilized: May 2016)
    5/13/2016 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 85028/5A:2016-05-13

    CONNECTOR, ELECTRIC, RECTANGULAR, INDIVIDUAL CONTACT SEALING, POLARIZED CENTER JACKSCREW, WIRE SEAL, SIZE 16, CRIMP REMOVABLE CONTACTS (Stabilized: May 2016)
    5/13/2016 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 6323:2016-02-24

    FITTING ASSEMBLY, EXTENDED UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI
    2/24/2016 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5828A:2015-12-02

    FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD
    12/2/2015 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5864A:2015-12-02

    FITTING END, BULKHEAD, 24° CONE, FLARELESS, FLUID CONNECTION, DESIGN STANDARD
    12/2/2015 - PDF - English - SAE
    Learn More
    €77.00

  • 15/30328090 DC:2015

    BS SP 94 AMD3. Specification for bronze oil-retaining bushes and thrust washers. For aircraft
    10/22/2015 - PDF - English - BSI
    Learn More
    €23.70

  • SAE J 2655:2015-09-22

    Fastener Part Standard - Washers and Lockwashers (Inch Dimensioned)
    9/22/2015 - PDF - English - SAE
    Learn More
    €77.00

  • DIN EN 16602-70-46:2015-06

    Space product assurance - Requirements for manufacturing and procurement of threaded fasteners, English version EN 16602-70-46:2014
    6/1/2015 - PDF - English - DIN
    Learn More
    €103.00

  • SAE AS 5827A:2015-04-23

    FITTING END, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD
    4/23/2015 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 870E:2015-02-17

    WRENCHING CONFIGURATION, BI-HEXAGONAL (12 POINT) DRIVE, DESIGN STANDARD FOR (Stabilized: Feb 2015)
    2/17/2015 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 18280 SUP 1A:2015-01-20

    Fittings, 24° Cone Flareless, Fluid Connection, 3000 psi (Supplement 1)
    1/20/2015 - PDF - English - SAE
    Learn More
    €77.00

  • UNE-EN 16602-70-46:2014

    Space product assurance - Requirements for manufacturing and procurement of threaded fasteners (Endorsed by AENOR in December of 2014.)
    12/1/2014 - PDF - English - AENOR
    Learn More
    €72.00

  • BS EN 16602-70-46:2014

    Space product assurance. Requirements for manufacturing and procurement of threaded fasteners
    11/30/2014 - PDF - English - BSI
    Learn More
    €253.59

  • NBN EN 16602-70-46:2014

    Space product assurance - Requirements for manufacturing and procurement of threaded fasteners
    11/28/2014 - PDF - English - NBN
    Learn More
    €77.00

  • NBN EN 16602-70-46:2014

    Space product assurance - Requirements for manufacturing and procurement of threaded fasteners
    11/28/2014 - PDF - French - NBN
    Learn More
    €77.00

  • SAE AIR 1551B:2014-07-29

    Torque Tightening Metric Screw Threaded Fasteners (Stabilized: Jul 2014)
    7/29/2014 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 1159C:2014-07-08

    Wrenching Configuration, 12 Lobed, For Threaded Fasteners (Stabilized: Jul 2014)
    7/8/2014 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 3503:2019-04-09

    INSERT, SCREW THREAD, SELF LOCKING PLASTIC LOCKING DEVICE, SOLID FILM LUBRICATED, SELF-BROACHING KEYS, OVERSIZE UNS S66286
    4/24/2014 - PDF - English - SAE
    Learn More
    €77.00

  • SAE MA 1586A:2019-05-10

    Wrench Configuration, 12 Spline Drive, Metric
    9/26/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5270:2013-09-19

    Bolts, Screws and Studs, Nickel Alloy, UNS N07718 Work-Strengthened, Tensile Strength 220 ksi Procurement Specification
    9/19/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE ARP 4402:2013-06-11

    Eddy Current Inspection of Open Fastener Holes in Aluminum Aircraft Structure
    6/11/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE J 2277:2013-04-24

    Shot Peening Coverage Determination
    4/24/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE MA 4360A:2013-03-18

    Metric Wrenches: 6 & 12 Point Flare Nut, Non-distorting
    3/18/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE MA 4535A:2013-02-10

    Wrenches, Box and Open End Combination Twelve Point, High Strength, Thin Wall, Metric (Stabilized: Feb 2013)
    2/10/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/9:2013-01-09

    BAND, MALE COUPLING, 6 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/8:2013-01-09

    BAND, FEMALE COUPLING, 6 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/7:2013-01-09

    BAND, MALE COUPLING, 12 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/6:2013-01-09

    BAND, FEMALE COUPLING, 12 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/5:2013-01-09

    COUPLING, MALE, 6 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/4:2013-01-09

    COUPLING, FEMALE, 6 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/3:2013-01-09

    COUPLING, MALE, 12 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/2:2013-01-09

    COUPLING, FEMALE, 12 INCH AIR DUCT
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365/1:2013-01-09

    PIN, FEMALE COUPLING
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 7365:2013-01-09

    Duct Assembly, Ground, Conditioned Air, Metallic Reinforced, Low Pressure, 350 °F
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5863:2013-01-09

    FITTING END, 24° CONE, FLARELESS, FLUID CONNECTION, DESIGN STANDARD
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5529:2013-01-09

    SLEEVE, FLARELESS TUBE FITTING, INTERNALLY SWAGED
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5530:2013-01-09

    UNION, FLARELESS TUBE FITTING, INTERNALLY SWAGED
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5531:2013-01-09

    UNION, SHORT FLARELESS TUBE FITTING, INTERNALLY SWAGED
    1/9/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5229:2013-01-07

    PORT, INTERNAL STRAIGHT THREAD, AIR CONNECTION, DESIGN STANDARD
    1/7/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5449:2013-01-07

    FITTING END, WELD RING, SHORT TAPERED, DESIGN STANDARD
    1/7/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5039:2013-01-07

    FITTING, BODY END - THREADED COUPLING, RIGID, SELF-BONDING, DESIGN STANDARD
    1/7/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE ARP 4988:2013-01-02

    Procedure for Determining Thrust Wire Lengths and Minimum Insertion Depths
    1/2/2013 - PDF - English - SAE
    Learn More
    €77.00

  • SAE ARP 1135B:2012-12-05

    Standardization of Drive End of Hydraulic or Geared Torque Wrenches for Use to an Upper Limit of 500,000 inch pounds (Stabilized: Dec 2012)
    12/5/2012 - PDF - English - SAE
    Learn More
    €77.00

  • SAE MA 1547A:2019-05-10

    Wrenches, Twelve Spline, Metric
    11/19/2012 - PDF - English - SAE
    Learn More
    €77.00

  • SAE AS 5054A:2018-08-23

    Areas for Calculating Stress or Load Values for Externally and Internally Threaded Fasteners
    11/19/2012 - PDF - English - SAE
    Learn More
    €77.00

  • 12/30256197 DC:2012

    BS SP 94 AMD2. Specification for bronze oil-retaining bushes and thrust washers for aircraft
    3/13/2012 - PDF - English - BSI
    Learn More
    €23.70

  • SAE AS 954G:2011-12-09

    Wrenches, Hand, Twelve Point, High Strength, Thin Wall
    12/9/2011 - PDF - English - SAE
    Learn More
    €77.00

  • UNE-EN 3911:2010

    Aerospace series - Six lobe recess - Geometrical definition (Endorsed by AENOR in December of 2010.)
    12/1/2010 - PDF - English - AENOR
    Learn More
    €24.00

  • BS EN 3911:2010

    Aerospace series. Six lobe recess. Geometrical definition
    11/30/2010 - PDF - English - BSI
    Learn More
    €130.35

  • NBN EN 3911:2010

    Aerospace series - Six lobe recess - Geometrical definition
    11/26/2010 - PDF - German - NBN
    Learn More
    €45.00

  • NBN EN 3911:2010

    Aerospace series - Six lobe recess - Geometrical definition
    11/26/2010 - PDF - English - NBN
    Learn More
    €45.00

  • ECSS-Q-ST-70-46C Annex A

    Customer specification document for threaded fasteners
    3/6/2009 - PDF - English - ECSS
    Learn More
    €25.00

  • ECSS-Q-ST-70-46C Annex B

    Product conformance report (PCR)
    3/6/2009 - PDF - English - ECSS
    Learn More
    €25.00

  • ECSS-Q-ST-70-46C

    Requirements for manufacturing and procurement of threaded fasteners
    3/6/2009 - PDF - English - ECSS
    Learn More
    €25.00

  • NF EN 3043, L24-111 (01/2009)

    Aerospace serie - Fasteners, externally threaded, in heat resisting steel FE-PA92HT (A286) - Classification : 900 MPa/650 °C, Manufacturing method optional - Technical specification - Série aérospatiale
    1/1/2009 - Paper - English, French - AFNOR
    Learn More
    €100.63

  • NBN EN 3368:2008

    Aerospace series - Aerospace design standard - Holes for locating pins
    11/26/2008 - PDF - English - NBN
    Learn More
    €45.00

  • NBN EN 3201:2008

    Aerospace series - Holes for metric threaded fasteners - Design standard
    11/26/2008 - PDF - German - NBN
    Learn More
    €45.00

  • NBN EN 3201:2008

    Aerospace series - Holes for metric threaded fasteners - Design standard
    11/26/2008 - PDF - English - NBN
    Learn More
    €45.00

  • NBN EN 2786:2008

    Aerospace series - Electrolytic silver plating of fasteners
    11/26/2008 - PDF - German - NBN
    Learn More
    €45.00

  • NBN EN 2786:2008

    Aerospace series - Electrolytic silver plating of fasteners
    11/26/2008 - PDF - English - NBN
    Learn More
    €45.00

  • NBN EN 3782:2008

    Aerospace series - Holes for 100° countersunk head screws - Design standard
    11/1/2008 - PDF - English - NBN
    Learn More
    €45.00

  • NBN EN 3043:2008

    Aerospace series - Fasteners, externally threaded, in heat resisting steel FE PA92HT (A286) - Classification: 900 MPa/650 °C, manufacturing method optional - Technical specification
    11/1/2008 - PDF - German - NBN
    Learn More
    €56.00

  • NBN EN 3043:2008

    Aerospace series - Fasteners, externally threaded, in heat resisting steel FE PA92HT (A286) - Classification: 900 MPa/650 °C, manufacturing method optional - Technical specification
    11/1/2008 - PDF - English - NBN
    Learn More
    €56.00

  • NF EN 2786, L22-032 (08/2008)

    Aerospace series - Electrolytic silver plating of fasteners - Série aérospatiale
    8/1/2008 - Paper - English, French - AFNOR
    Learn More
    €64.01

  • NF EN 3201, L20-032 (08/2008)

    Aeraospace series - Holes for metric threaded fasteners - Design standard - Série aérospatiale
    8/1/2008 - Paper - English, French - AFNOR
    Learn More
    €73.30

  • NF EN 3368, L20-027 (08/2008)

    Aerospace series - Aerospace design standard - Holes for locating pins - Série aérospatiale
    8/1/2008 - Paper - English, French - AFNOR
    Learn More
    €64.01

  • BS EN 3782:2008

    Aerospace series. Holes for 100° countersunk head screws. Design standard
    7/31/2008 - PDF - English - BSI
    Learn More
    €130.35

  • BS EN 3043:2008

    Aerospace series. Fasteners, externally threaded, in heat resisting steel FE PA92HT (A286). Classification: 900 MPa/650 °C, manufacturing method optional. Technical specification
    7/31/2008 - PDF - English - BSI
    Learn More
    €215.67

  • UNE-EN 3782:2008 (R2018)

    Aerospace series - Holes for 100° countersunk head screws - Design standard (Endorsed by AENOR in July of 2008.)
    7/1/2008 - PDF - English - AENOR
    Learn More
    €28.00

  • UNE-EN 3043:2008

    Aerospace series - Fasteners, externally threaded, in heat resisting steel FE PA92HT (A286) - Classification: 900 MPa/650 °C, manufacturing method optional - Technical specification (Endorsed by AENOR in July of 2008.)
    7/1/2008 - PDF - English - AENOR
    Learn More
    €68.00

  • BS EN 3201:2008

    Aerospace series. Holes for metric threaded fasteners. Design standard
    5/30/2008 - PDF - English - BSI
    Learn More
    €130.35

  • UNE-EN 2786:2008 (R2018)

    Aerospace series - Electrolytic silver plating of fasteners (Endorsed by AENOR in May of 2008.)
    5/1/2008 - PDF - English - AENOR
    Learn More
    €28.00

  • UNE-EN 3201:2008

    Aerospace series - Holes for metric threaded fasteners - Design standard (Endorsed by AENOR in May of 2008.)
    5/1/2008 - PDF - English - AENOR
    Learn More
    €46.00

  • UNE-EN 3368:2008

    Aerospace series - Aerospace design standard - Holes for locating pins (Endorsed by AENOR in May of 2008.)
    5/1/2008 - PDF - English - AENOR
    Learn More
    €38.00

  • BS EN 3368:2008

    Aerospace series. Aerospace design standard. Holes for locating pins
    4/30/2008 - PDF - English - BSI
    Learn More
    €130.35

  • BS EN 2786:2008

    Aerospace series. Electrolytic silver plating of fasteners
    4/30/2008 - PDF - English - BSI
    Learn More
    €130.35

  • SAE AS 4723:2018-08-23

    Insert, Screw Thread, Self-Locking, UNS S66286, Key Locked, Plastic Self Locking Device, Solid Film Lubricant Procurement Specification For
    7/5/2007 - PDF - English - SAE
    Learn More
    €77.00

  • ASD-STAN prEN 6117 (12/31/2006)

    Aerospace series - Specification for lubrication of fasteners with cetyl alcohol
    12/31/2006 - PDF - English - ASD-STAN
    Learn More
    €25.79

  • ASD-STAN prEN 6095 (10/31/2006)

    Aerospace series - Rotary fasteners - Structural and non-structural applications - Technical specification
    10/31/2006 - PDF - English - ASD-STAN
    Learn More
    €60.38

  • NF L22-031 (09/2003)

    Fasteners - Selection of metallic materials
    9/1/2003 - Paper - French - AFNOR
    Learn More
    €51.24

  • MIL-T-7743:1999

    TESTING, STORE SUSPENSION AND RELEASE EQUIPMENT, GENERAL SPECIFICATION FOR
    9/15/1999 - PDF sécurisé - English - DODNAV
    Learn More
    €25.00

  • BS 2A 294:1998

    Spline drives. Wrenching configuration. Metric series
    7/15/1998 - PDF - English - BSI
    Learn More
    €130.35

  • BS A 323:1998

    Bihexagonal drives. Wrenching configuration. Metric series
    5/15/1998 - PDF - English - BSI
    Learn More
    €130.35

  • NBN EN 3611:1995

    Aerospace series - Spigots - Dimensions and fit selection - Design standard
    12/29/1995 - PDF - German - NBN
    Learn More
    €45.00

  • NBN EN 3611:1995

    Aerospace series - Spigots - Dimensions and fit selection - Design standard
    12/29/1995 - PDF - English - NBN
    Learn More
    €45.00

  • NBN EN 3611:1995

    Aerospace series - Spigots - Dimensions and fit selection - Design standard
    12/29/1995 - PDF - French - NBN
    Learn More
    €45.00

  • BS EN 3611:1995

    Spigots. Dimensions and fit selection. Design standard
    11/15/1995 - PDF - English - BSI
    Learn More
    €130.35

  • MIL-T-7743:1993

    TESTING, STORE SUSPENSION AND RELEASE EQUIPMENT, GENERAL SPECIFICATION FOR
    4/30/1993 - PDF sécurisé - English - DODNAV
    Learn More
    €25.00

  • DIN 65121:1992-10

    Aerospace; bolts, screws, nuts and associated parts; survey and selection for workshop; inactive for new design
    10/1/1992 - PDF - German - DIN
    Learn More
    €54.80

  • NF L20-010 (05/1989)

    Aerospace series. Equipment. Choice of fasteners, NF E series. - Aéronautique et espace
    5/1/1989 - Paper - French - AFNOR
    Learn More
    €29.39

  • BS A 297:1987

    Specification for internal drive, offset cruciform recess (Torq-Set(R)) for rotary fastening devices. Metric series
    3/31/1987 - PDF - English - BSI
    Learn More
    €130.35

  • UNE 28557:1983

    FASTENERS FOR AEROSPACE CONSTRUCTION-BI-HEXAGONAL WREANCHING
    11/15/1983 - PDF - Spanish - AENOR
    Learn More
    €13.00

  • DIN ISO 4095:1980-12

    Aerospace; fasteners for aerospace construction, bi-hexagonal wrenching configuration
    12/1/1980 - PDF - German - DIN
    Learn More
    €23.80

  • BS A 273:1978

    Specification for gauging practice for 100° countersunk head fasteners for flushness control
    1/31/1978 - PDF - English - BSI
    Learn More
    €130.35

  • BS A 272:1977

    Specification for Hi-torque speed drive recess: dimensions and gauging for countersunk head fasteners
    4/29/1977 - PDF - English - BSI
    Learn More
    €75.84

123 Item(s)

Set Ascending Direction
per page

List  Grid